I assume you are using Lon Gateway?

 

SetupMS3 is available, but you might want to add your email address to your profile so a good samariton could send it to you

I was under the impression that the D-BACS came pre-configured with bacnet points and it was just a case of configuring it to your system, but I'm no expert so don't quote me on that...

 

Picnik, we have an BACnet D-BACS interface that we are having issues with. The daiken rep came out and said that we have to tell the "master" unit what mode to be in. Does this sound right? Is setup MS3 difficult to navigate? What little bit I saw of it didn't seem to bad.

 

There is no point configuration in the gateway. The excel file is for generating a points list including object IDs and instance numbers. This is typically useful for integrators who cannot autodiscover.

Xarralu, assuming you have a heat pump system, mode change command through the gateway will have to be sent to the unit designated changeover master. Mode change command will be ignored by units on the system which are not the master.

 

Thanks, El Presidente. Just needed someone else to say the same thing before I change all of the programs.

 

You're welcome.

 

Any chance of sending it to me too?

 

Hey,

Picknik, I am also wondering if you can send me SetupMS3... I have had a terrible time getting an up to date version of this software. I currently have SetupDBACS.. It's basically the same as SetupMS3, though much older. The file version is 3.0.0.1, dated 2002.. Anyways, all I need the tool for is to change the BACnet IP udp port number to something other than 47808. I need to use 47811, and this old version of the tool doesn't support it. The current documentation states the need to use SetupMS3.exe I believe 6 > for this. My main problem is getting in touch with our Regional Daikin AC rep in New England. We have several Silver Daikin D-bacs we use to Integrate with BACnet. And have had much success, though I am running into problems using the Default ports on a few jobsites. Any help is appreciated, if you are unwilling to provide the Service tool, do you know who I would need to Call at Daikin AC for this tool? I work out of Warwick, Rhode Island USA..

Thank!

Steve

 

Hi Steve

If you did not manage to find SetupBACnet send me an email to attach you the software.

 

Hi Livaldi,

Thank you for responding, I have returned in a bit and didn't see your reply! I thought I had my settings set to e-mail when I watch this thread!

I'f you have an up-to-date copy of Setupdbacs.exe thhat would be great,

My email is: Removed E-mail Address

I appreciate your time! Thank you


Please put email in your profile

 

Hi Livaldi,

Thank you for responding, I have returned in a bit and didn't see your reply! I thought I had my settings set to e-mail when I watch this thread!

I'f you have an up-to-date copy of Setupdbacs.exe thhat would be great,

My email is: Removed E-mail Address

I appreciate your time! Thank you


Please put email in your profile

ssorel,

Should you have you're email alert now setup, you need to place you're email address in your profile so people can contact you :rules:

:Faint:

 

Hi steve

You will receive an email from sendspace. I attached all the documents and programs that i had for DAIKIN D-BACS.
Hope that these will help

 

hi to all
im new to this
does someone have the setup MS3 software they can email to me
i am trying to discover the bacnet points on a DMS502B51 WITH A TRIDIUM jace 600
using bacnet/ip, and it cannot discover this daikin box. perhaps it needs to be enable with this software
Daikin dont know what im talking about?
any help is much appreciated
Stan

 

Stan,

Can you ping the gateway but not discover points? Are you on a different subnet than the gateway? If so the gateway might have to be setup as a foreign device.

Pres

 

me too facing the same issue can u please send me the setup tool.

 

yes i can ping it
but it wont discover

 

What IPs for the jace and the gateway? I'll send you the setup tool.

Pres

 

Hi El Presidente

Please would you send me the setup tool. I cannot find the copy I had as I don't use it very often and I changed laptops.

Much appreciated...

 

Presidente, could you send the setup tool to me as well?
thanks.

 

amigo, check your mail.

Pres

 

Gracias.

 

Thanks much appreciated
I'm using a web /jace600 with bacnet over ip and have the second port enabled with the ip address of the Daikin bacnet box 192.168.0.1 which is the default ip address
I can ping the Daikin box directly through the pc however the Jace can't discover anything when connected in!
All I want to see weather bacnet is enabled in the Daikin box and if so then the problem possibly is with the jace.
So a start is to see with this software if bacnet is enabled??
Thanks again
Regards
Stan

 

De nada and you're welcome.

 

Ok, what's the IP address of the Jace? It will have to be 192.168.0.X if the gateway is left at default IP of 192.168.0.1 without enabling the gateway as a foreign device.

If it is on a different subnet, say 192.168.1.1, foreign device will have to be enabled inside the gateway and this IP address must be put in so the gateway can send out a request to be added to the BBMD foreign device table.

BACnet does not need to be enabled. As long as the battery backup switch is turned on and it has an IP address, it is ready to rock. Is the VRV system already connected to the gateway? If not, you will get no points.

Pres

 

Please for the love of everything that is holy send me the setup tool too.

Getting this from Daikin has proved to be more difficult than pulling 5 girls home from an FHM event.

Thanks in advance. my email address is in my sig

 

Is there any chance someone could send me SetupMS3? I can't get a response from Daikin and really need this tool. Thank you.

 

threefiddy, check your mail.

Pres

 

El Presidente,
Could I please get a copy of the MS3 software too, I am trying to configure a Daikin Gateway, and I need to set a custom static IP, not sure if there is any other way to do so?

 

C, add an email to your profile.

Pres

 

Thanks alot, email added.

 

C, check your mail.

threefiddy, my e-mail bounced back. Not sure what the problem is.

Pres

 

Is there any chance someone could send me SetupMS3 please? I have to change to default IP address for it to talk to our BMS.

Thankyou in advance.

 

sent